AT&T 1815 Bedienungsanleitung Seite 14
- Seite / 14
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
The telephone can store 9 telephone numbers, each up to 24 digits
long. A number remains stored in memory unless you change it
by storing a new number in its place.
NOTE: You may choose to store emergency numbers in memory
locations. This feature is provided only as a convenience and the
manufacturer assumes no responsibility for customer reliance upon
the memory feature.
Storing Memory Numbers
1 Press and release G.
2 Enter a telephone number (up to 24 digits). To store a
switchhook flash, press F in the appropriate
place while entering the number. To store a dialing
pause, press p in the appropriate place while
entering the number.
3 Press and release Y.
4 Press and release the memory location (1 to 9) where
the number is to be stored. You cannot use 0, # or *
as memory locations.
Dialing Memory Numbers
1 Lift the handset.
2 Press and release Y.
3 Press and release the memory location (1 to 9).
Storing Numbers Just Dialed
1 Press and release G.
2 Press and release R.
3 Press and release Y.
4 Press and release the memory location (1 to 9) where
the number is to be stored.
TELEPHONE MEMORY
Temporary Tone
Dial numbers in
telephone memory.
Store numbers in
telephone memory.
Store a pause in a
memory dialing
number.
Light is on when
phone line is in use.
When light goes on,
battery needs to be
replaced.
Access telephone
subscriber services.
Put caller on Hold.
(Light goes on when
call is on Hold.)
Mute handset
microphone.
Redial last
number called.
Adjust listening volume
during a call.
Recording a Memo
You can record a memo to be stored as an incoming message.
The memo can be up to 3 minutes long, and will be played back
with other messages.
1 Press and release M. After the beep, speak
toward the microphone.
2 To stop recording, press S.
When Memory is Full
The system can record approximately 12 minutes of messages,
including your announcement, for up to a total of 99 messages.
When memory is full, or 99 messages have been recorded, the
Message Window flashes F. Delete messages to make room for
new ones.
When memory is full, the system answers calls after 10 rings, and
sounds 2 beeps instead of playing your announcement.
Remote Access Code
You can use many features of this answering system remotely from
a touch tone phone. Most features can be accessed only after you
enter a Remote Access Code, preset to 500. You can view the
Remote Access Code by tapping c.
ANSWERING SYSTEM OPERATION
You can change the Remote Access Code to any 3-digit number
from 500-999.
1 Press and release g. The Message Window
displays CH.
2 Press and release c. The system announces “First
digit.”
3 Press / or ? to change the digit.
4 When the Message Window displays the desired first
digit, press and release c. The system announces
“Second digit.”
5 Press / or ? to change the digit.
6 When the Message Window displays the desired
second digit, press and release c. The system
announces “Third digit.”
7 Press / or ? to change the digit.
8 When the Message Window displays the desired third
digit, press and release c. The system announces
the new Remote Access Code.
Playing Messages
1 Dial your telephone number from a touch tone phone.
2 When the system answers, enter your Remote Access
Code. The system announces the number of messages
received, then beeps twice.
3 After the two beeps, wait 4 seconds, and the system
plays back messages
— OR —
Press and release 1 to play all messages
— OR —
Press and release 2 to play only new messages (if
there are no new messages, the system announces “No
new messages”).
4 To repeat a message — Press and release 4 while the
message is playing.
To repeat part of a message — Hold down 4. To
resume playing, release 4.
To skip a message — Press and release 6 while the
message is playing.
To skip part of a message — Hold down 6. To
resume playing, release 6.
To stop message playback — Press and release 5.
To save messages, hang up.
Deleting Messages
To delete selected message — Press and release 3 while
the message is playing.
To delete all messages — After you have listened to all
messages and heard the 2 beeps, press 3, 3.
Recording Announcement
1 Press 7, *.
2 Speak after the beep, then press 5 to stop recording.
The system replays your new announcement.
To review your announcement — Press 7, 1.
Recording a Memo
1 Press # and begin speaking after the beep.
2 Press 5 when you are finished.
Room Monitor with Intercom
You can call the answering system and listen to any activity in the
room.
1 Press 9, 1 to listen for 30 seconds.
2 If you wish, you can press 1 while the monitor is
active to speak to someone in the room (up to 30
seconds).
3 Press 1 again during intercom operation to return to
listening only.
4 Press 5 at any time to exit Room Monitor with
Intercom.
Ending Remote Access Call
Press *, 9. The system announces “The machine will now hang
up,” and disconnects from the line.
Changing Remote Access Code
1 Press 9 9. The system announces “Enter new code.”
2 Enter your new Remote Access Code, any number
between 500 and 999.
3 If a valid code is entered, the system announces the
new Remote Access Code. If an invalid code is
entered, the system beeps 5 times rapidly, then beeps
twice. Repeat Steps 1 and 2.
Turn System Off
Press 8, 8.
Turn System On
When the system is off, it answers after 10 rings and beeps twice.
1 Press 0 to turn the system on.
2 The system beeps twice and is ready to answer calls
and record messages. If the system beeps 5 times, the
memory is full.
Memory Full
If the system answers after 10 rings and beeps twice instead of
playing your announcement, it might be off or memory might be
full.
1 Enter Remote Access Code after 2-beep signal.
2 Listen to messages, and delete some or all of them.
3 Press 0 to make sure your system is on before you
hang up.
ANSWERING SYSTEM OPERATION
From a Remote Touch Tone Phone
Answering Calls
When the system answers a call, the caller hears the announce-
ment you recorded, followed by a beep. After the beep, the
system begins recording your caller’s message. A caller can leave
a message up to 3 minutes long. If the message is longer than 3
minutes, or if the caller is silent for more than 7 seconds, or if the
system runs out of memory, the system beeps once and hangs up.
Frequent callers can skip over your announcement by pressing #.
Ring Select/Toll Saver
Use the RING SELECT switch on the back of the system to
select how many times the line will ring before the system
answers a call. Set to 2 for two rings, set to 4 for four rings, or set
to TS for Toll Saver. When you set the system to TS, the system
answers after 4 rings when you have no new messages, and after 2
rings when you have new messages.
Message Window
The Message Window displays the number of messages that have
been recorded. If the Message Window displays F, then the
memory is full and you’ll need to delete messages before new
ones can be recorded.
PLAY Light
The PLAY Light blinks when you have new messages, and
remains steady when you have messages in memory that you’ve
already played. The PLAY Light is off when there are no
messages in memory.
Call Screening/Intercept
Set the system to answer calls, and set the volume control so you
can hear the caller’s message.
If you decide to take the call, lift the handset of this phone or any
phone on the same line. The system stops recording and resets to
answer calls.
Listening to Your Messages
As the system plays back messages, the Message Window
displays the number of the message playing. Before playing each
message, the system announces the day and time the message was
received. After playing the last message, the system announces
“End of messages.”
Play all messages — Press and release P. If you
have no messages, the system announces “No messages.”
Play new messages only — Hold down P for about
2 seconds, until the system begins playing. If you have
no new messages, the system announces “No new
messages.”
Repeat entire message — Press and release ?.
Repeat part of message — Hold down ? for a
few seconds, then release it to resume playing. The
system beeps while the button is held down.
Skip to next message — Press and release /.
Skip part of a message — Hold down / for a
few seconds, then release it to resume playing. The
system beeps while the button is held down.
Stop message playback — Press and release S.
Privacy Playback
Instead of hearing your messages through the system’s speaker,
you can listen to them through the answering system handset.
1 Hold down S while you lift the handset.
2 Press and release P to play all messages
— OR —
Hold down P for about 2 seconds to play new
messages only.
3 After pressing P, you can follow the directions
above to repeat, skip, or stop message playback.
NOTE: Privacy Playback will not work if you have answered a
call, or if you lift the handset and place a call before pressing P.
Saving Messages
The system saves your messages automatically if you do not
delete them. The system can save about 12 minutes of messages,
including your announcement, for up to a total of 99 messages.
When memory is full, you must delete some or all messages
before new messages can be recorded.
Deleting Messages
Delete all messages — Hold down D. The system
announces “Messages deleted” and the MessageWindow
displays 0. If you haven’t listened to all of the messages,
the system beeps 5 times, and does notdelete messages.
Delete selected messages — Press and release D
while the message you want to delete is being played.
The system beeps once, and continues with the next
message. If you want to check a message before you
delete it, you can press ? to replay a message
before deleting it.
When the system reaches the end of the last message, the
messages not deleted are renumbered, and the Message
Window displays the total number of messages remaining
in memory.
ANSWERING SYSTEM OPERATION
Setting the Clock
You’ll need to set the clock so that it can record the day and time
that each message is received.
1 Press and release g. The Message Window
displays CH.
2 Press and release C. The current day setting is
announced.
3 To change the day setting, hold down / or
? until the correctday is announced. Then
release the button.
4 Press and release C. The current hour setting is
announced.
5 To change the hour setting, hold down / or
? until the correcthour is announced. Then
release the button.
6 Press and release C. The current minutes setting is
announced.
7 To change the minutes setting, hold down / or
? until the correct minutes setting is
announced. Then release the button.
8 Press and release C. The new day and time are
announced.
To check the clock, press and release C.
Recording Your Announcement
Before using this answering system, you should record the an-
nouncement (up to 3 minutes long) that callers will hear when the
system answers a call. If you choose not to record an announce-
ment, the system answers with a prerecorded announcement:
“Hello. Please leave a message after the tone.”
1 Press and release g. The Message Window
displays CH.
2 Press and release A. The system beeps. Speak
toward the microphone normally, from about 9 inches
away. While you are recording, the Message Window
displays the elapsed time of your recording.
3 Press S when you are finished. The system
automatically plays back your announcement.
To review your announcement, press and release A.
Turning the System On/Off
Use O to turn the system on and off. When the system is off,
the Message Window is blank.
Volume Control
Use V to adjust the volume of the system’s speaker. Press the top
arrow to increase volume. Press the bottom arrow to decrease volume.
ANSWERING SYSTEM OPERATION
Adjust listening volume
during message playback.
Set and hear time/day.
Record and hear outgoing announcement.
Repeat all or part of a message.
Stop message playback.
Microphone
Skip all or part of a message.
Delete all or selected messages.
Play messages.
Turn system on or off.
Displays number of messages
and other indicators.
Select number of times line
rings before system answers
(RING SELECT on back).
Use with other buttons to change settings.
Set and hear
Remote Access Code.
Mute
Mute lets you hear the other party, but prevents the other party
from hearing you.
To mute a call, press and release m. The MUTE light
goes on.
To return to two-way conversation, press and release m.
Flash
Press and release F instead of pressing the switchhook to ac-
tivate services such as Call Waiting or Three-Way Calling. You
might have to press other buttons before or after F as explained
in the custom calling instructions provided by your service pro-
vider.
Temporary Tone
If you have dial pulse (rotary) service, this feature allows you to
enter codes or tones needed to operate answering machines, or
use electronic banking services, calling cards, and other special
services. This feature will operate most special services; how-
ever, some services may actually require a touch tone line. To be
sure, ask the company that provides the special service.
NOTE: If you have touch tone service, you do not need to use the
Temporary Tone feature.
1 Dial the call, then press and release * (TONE). Any
buttons pressed after this will send tone signals.
2 After you hang up, the phone automatically returns to
dial pulse (rotary) dialing.
Dial Mode
This phone comes set to operate with touch tone service. If you
have dial pulse (rotary) service, you will need to reset the dial
mode. If you hear clicks (not tones) when you dial, you have dial
pulse (rotary) service.
To change to dial pulse mode:
1 Press and release G.
2 Press #, #, #, 3.
To change back to touch tone mode:
1 Press and release G.
2 Press #, #, #, 8.
Ringer Volume
Use the RINGER switch located on the right side of the phone to
turn the ringer OFF, or to set it to LO or HI volume. You can
make or answer calls when the ringer is off, and other phones on
the same line are not affected by the setting.
Handset Volume Control
While on a call, use V to adjust the listening level. Press the
top arrow to increase volume. Press the bottom arrow to decrease
volume.
Redial
Press and release R to dial the last number you dialed (up to
32 digits). The last number you dialed is stored in redial memory
until you dial another number.
Hold
To put a call on hold, press and release H. The HOLD light
flashes. You can return the handset to the cradle without discon-
necting the call.
To take a call off hold, press and release H
— OR —
Lift the handset of this phone
— OR —
Lift the handset of another phone on the same line as this
phone.
TELEPHONE OPERATION
1815 map_2ATT 3/23/99, 10:19 AM2
Verwandte Produkte und Handbücher für Anrufbeantworter Geräte AT&T 1815
(2 Seiten)
(48 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern