AT&T Call Management System Bedienungsanleitung Seite 201
- Seite / 227
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
ADDITIONS
On the System Parameters-Customer Options Form, set the Distributed
Communications System (DCS) field to “y” to enable the feature.
Administer the other required translation data using the forms listed under
Distributed Communications System (DCS) in the AT&T System 75 and
System 75 XE—Implementation, 555-200-651 (R1V2), 555-200-652 (R1V3).
Save Translations
1.
Enter save translations. Press the RETURN key. This command
instructs the system to take all translation information in memory
and write it onto the tape.
2. Update backup tape, if required.
189
- AT&T System 75 1
- And System 75XE 1
- TO ORDER 2
- OF THIS 2
- TO COMMENT ON THIS MANUAL 2
- Contents 3
- . . 9
- . . . . .208 10
- ● . ● 0. ● * 12
- INTRODUCTION 13
- ORGANIZATION 14
- UPGRADE PROCESS SYSTEM 75 15
- 2. Software Upgrade 18
- 555-200-500 20
- Updating 20
- Version 2 System Features 20
- 3. Prerequisite Hardware 21
- Figure 8 34
- (Component Side) 34
- Customer’s Translations 38
- Version 2 Translations 38
- VERSION 3 40
- Basic V2 to V3 Upgrade 41
- 1. Hardware Upgrades 41
- 2 (TN720/TN738), and 42
- 2. Software Upgrades 43
- 4. Service Interruption 46
- Circuit Pack 49
- Assign Version 3 53
- Translations 53
- Create Tape Backup 54
- Port Assignment Record 55
- UPGRADE PROCESS SYSTEM 56
- Out and Remove Hunt 61
- Groups To Be Rearranged 61
- Add or Replace Circuit 63
- Assign Version 3 Translations 65
- SUBSYSTEM UPGRADE 68
- PROCEDURE FOR UPGRADES 69
- SMALL CABINET CONTROL CARRIER 78
- Down System 79
- Replace Control Carrier 79
- PREREQUISITES 82
- ● 20 B25A Connector Cables 83
- PROCEDURE FOR UPGRADE 84
- Figure 13 86
- Figure 14 89
- Figure 15 91
- Pallet-Mounted System 75 91
- Figure 16 92
- Ramps Installed on Pallet 92
- CABINET (REAR VIEW) 95
- Figure 17 95
- Figure 22 102
- Power Up System 103
- Figure 23 104
- UPGRADE TRANSLATIONS 107
- Performed On-Site 109
- ADDITIONS 112
- Figure 24 113
- Figure 25 114
- Blank Circuit Pack Faceplate 114
- Figure 26 115
- Service Interruption 126
- Verify System Status 126
- Save Translations 126
- Power Down System 126
- Install Port Carrier 127
- Added Translations 129
- Update Port Assignment Record 129
- REAR VIEW 133
- Figure 32 134
- Bus Wiring Diagram 134
- Unpack and Inspect for Damage 137
- Figure 35 139
- Figure 36 140
- AC Power Requirements 140
- Position Port Cabinets 141
- Connect TDM Bus Cables 141
- DOOR LATCH 142
- Figure 37 142
- CABINET CLIP 143
- Figure 39 144
- TDM Bus Connections 144
- Install Ground Plate(s) 146
- Install Cabinet Clip(s) 148
- Install Cable Clamps 148
- Port Circuit Packs 148
- Install Cables 149
- Connect AC Power 149
- Enter Added Translations 150
- Figure 43 154
- Figure 44 155
- Ramps Installed 155
- Figure 45 156
- Auxiliary Cabinet 156
- 5. ADD ATTENDANT CONSOLE 157
- 6. ADD SELECTOR CONSOLE 158
- Figure 46. Selector 159
- CO, FX, WATS, AND PCOL TRUNKS 160
- 8. ADD DID TRUNKS 160
- 9. ADD TIE TRUNKS 161
- Table F 163
- DS1 TIE TRUNK SERVICE 164
- Add Circuit Packs 165
- SPEECH SYNTHESIS 167
- 12. ADD CODE CALLING ACCESS 167
- 13. ADD POOLED MODEM 168
- 14. ADD OFF-PREMISES AND 169
- OUT-OF-BUILDING TERMINALS 169
- 15. ADD EXTERNAL RINGING 170
- 18. ADD PagePac PAGING SYSTEM 172
- PagePac 20 173
- PagePac VS* 173
- PagePac 50/100/200 173
- 19. ADD MUSIC-ON-HOLD ACCESS 175
- 22. ADD INTEGRATED RECORDED 177
- ANNOUNCEMENT 177
- 23. ADD RECORDED TELEPHONE 178
- DICTATION ACCESS 178
- 24. ADD INADS INTERFACE 179
- 25. ADD APPLICATIONS 179
- INTERFACE (System 179
- PROCESSOR 179
- 75 Only) 179
- RECORDING INTERFACE 182
- EMERGENCY TRANSFER 184
- 28. ADD INFORMATION SYSTEM 185
- NETWORK INTERFACE 185
- INTERFACE 187
- (AUDIX) INTERFACE 190
- System Status 191
- 33. ADD PROPERTY MANAGEMENT 194
- SYSTEM (PMS) ACCESS 194
- TO REPLACE TWO 8-PORT ANALOG 195
- LINE CIRCUIT PACKS 195
- SYSTEM (DCS) INTERFACE 197
- System 75 198
- System 75 XE 198
- Make System Test Call 202
- Test Attendant Console 203
- Test Selector Console 204
- Test External Ringing 205
- Queue Warning Indicator 206
- Test Integrated Announcement 208
- Description 209
- Test Loudspeaker Paging 210
- Test Code Calling 210
- Test Music-on-Hold 211
- Emergency Transfer 212
- Test INADS Interface 213
- Test Tie Trunks 214
- Test DID Trunks 216
- Test CO Trunk 217
- Procedure—Incoming CO Trunk 218
- Interchange 219
- REFERENCES 220
- 75 and System 75 XE 224
Verwandte Produkte und Handbücher für Software AT&T Call Management System
Software AT&T MERLIN Attendant Betriebsanweisung
(42 Seiten)
(42 Seiten)
Software AT&T MERLIN Attendant Bedienerhandbuch
(650 Seiten)
(650 Seiten)
Software AT&T MERLIN Attendant Bedienerhandbuch
(100 Seiten)
(100 Seiten)
(6 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.135 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern